LinkBack URL
About LinkBacks
DFI Lanparty UT P45 T2RS/T3RS
*Sammelthread*
DFI Lanparty UT P45 T2RS/T3RS
Quelle: DFI Homepage
Schnellsuche
1.Technische Daten zum P45 T2RS/T3RS
2.BIOS, Treiber, Handbuch und Downloads
3.Kühlung
4.Verfügbarkeit
5.Speicherteiler
6.GTLs, GTL Tabelle, Max FSB, Messpunkte
7.Problemlösungen
8.OC Ergebnisse
9.Impressionen
1. Technische Daten zum DFI LP UT P45 T2RS/T3RS:
CPU
LGA 775 socket for: - Intel® Core2 Quad and Intel® Core2 Duo
Supports Intel Enhanced Memory 64 Technology (EMT64T)
Supports Enhanced Intel SpeedStep Technology (EIST)
Supports Intel Hyper-Threading Technology
Supports 1333/1066/800MHz FSB
Chipset
chipset - Northbridge: Intel® P45 Express chipset Intel® Fast Memory Access technology - Southbridge: Intel® ICH10R
System Memory
Four 240-pin DDR2 DIMM sockets
Supports DDR2 667/800/1066 MHz
Delivers up to 12.8Gb/s bandwidth
Supports dual channel (128-bit wide) memory interface
Supports up to 8GB system memory
Supports unbuffered x8 and x16 DIMMs
Expansion Slots
2 PCI Express (Gen 2) x16 slots (PCIE 1 and PCIE 3) - 2-way CrossFire at x8/x8 bandwidth - 2-way CrossFire + Physics at x8/x8/x4 bandwidth
1 PCI Express x1 slot (PCIE 2)
1 PCI Express x4 slot (PCIE 4)
3 PCI slots
BIOS
Award BIOS
8Mbit SPI flash memory
CMOS Reloaded
Audio
Bernstein audio module - Realtek ALC885 8-channel High Definition Audio CODEC - Center/subwoofer, rear R/L and side R/L jacks - Line-in, line-out (front R/L) and mic-in jacks - 2 coaxial RCA S/PDIF-in/out jacks - 1 optical S/PDIF connector - 1 CD-in connector - 1 front audio connector
DAC SNR/ADC SNR of 106dB/101dB
Full-rate lossless content protection technology
LAN
Marvell 88E8052 and Marvell 88E8053 PCIE Gigabit LAN controllers
Fully compliant to IEEE 802.3 (10BASE-T), 802.3u (100BASE-TX) and 802.3ab (1000BASE-T) standards
Storage
Intel ICH10R chip - Intel Matrix Storage technology - Supports up to 6 SATA devices - SATA speed up to 3Gb/s - RAID 0, RAID 1, RAID 0+1 and RAID 5
JMicron JMB363 PCI Express to SATA and PATA host controller - Supports up to 2 UltraDMA 100Mbps IDE devices - Supports 2 SATA devices - SATA speed up to 3Gb/s - RAID 0 and RAID 1
IEEE 1394
VIA VT6307
Supports two 100/200/400 Mb/sec ports
Rear Panel I/O1 Mini-DIN-6 PS/2 mouse port
1 Mini-DIN-6 PS/2 keyboard port
1 IEEE 1394 port
6 USB 2.0/1.1 ports
2 RJ45 LAN ports
Internal I/O
3 connectors for 6 additional external USB 2.0 ports
1 connector for an external COM port
1 connector for an IEEE 1394 port
1 connector for the Bernstein audio module
1 IrDA connector
1 CIR connector
8 Serial ATA connectors
1 40-pin IDE connector
1 floppy connector
1 24-pin ATX power connector
1 8-pin 12V power connector
2 4-pin 5V/12V power connectors (FDD type)
1 front panel connector
6 fan connectors
1 diagnostic LED
EZ touch switches (power switch and reset switch)
Power Management
ACPI and OS Directed Power Management
ACPI STR (Suspend to RAM) function
Wake-On-PS/2 / Wake-On-USB Keyboard/Mouse
Wake-On-LAN and Wake-On-Ring
RTC timer to power-on the system
AC power failure recovery
Hardware Monitor
Monitors CPU/system/Northbridge temperature and overheat alarm
Monitors Vcore/Vdimm/Vnb/VCC5/12V/V5sb/Vbat voltages
Monitors the speed of the cooling fans
CPU Overheat Protection function monitors CPU temperature and fan during system boot-up - automatic shutdown upon system overheat
PCB
6 layers, ATX form factor;
24.5cm (9.64") x 30.5cm (12")
All specifications above are subject to change without prior notice.
2. Bios, Treiber, Handbuch und Downloads:
Link zur DFI Homepage
Pressemitteilung von DFI
Empfohlene Speicherkits
Bios Downloads:
Final Bios
Beta Bios
3. Kühlung:
Die Aktuellen Kühler für P35/X38 und X48 sollten auch beim P45 passen!
Geizhals
200/667....3:5
200/800....1:2
266/667....4:5
266/800....2:3
266/1066...1:2
333/667....1:1
333/800....5:6
333/1066...5:8
400/800....1:1
Beim Release Bios besteht momentan ein Bug. Wenn man den JMicron SATA-Controller deaktiviert die Festplatte die an der ICH10r hängt nicht erkannt wird. Zum anfang einfach mal anlassen!
E3110 500x8
E3110 525x8
Speicherperformance 534x7,5 1:1
3DM 06 mit 2x 4870 im CF, karten @ 750/900
Q9550 470 x 8,5
Q9550 482 x 8,5
Q9550 494 x 8,5
Bios Tamplates:
FSB 470
FSB 494Code:>CPU Feature: Thermal Management Control.......... - Enabled PPM(EIST) Mode...................... - Enabled Limit CPUID MaxVal.................. - Enabled CIE Function........................ - Disabled Execute Disable Bit................. - Enabled Virtualization Technology........... - Enabled Core Multi-Processing............... - Enabled >DRAM Timing: Enhance Data transmitting........... - Fast Enhance Addressing.................. - Fast T2 Dispatch......................... - Disabled >Clock Setting Fine Delay Press Enter: DLL And RCOMP Settings.............. - Manual Ch1 Dram Defaul Skew................ - Model 3 Ch2 Dram Defaul Skew................ - Model 3 RCOMP Settings...................... - Model 1 Fine Delay Step Degree.............. - 70ps Ch1 Clock Crossing Setting.......... - Nominal DIMM1 Clock Fine Delay.............. - Current[1346ps] DIMM2 Clock Fine Delay.............. - Current[1346ps] Ch1 Control0 Fine Delay............. - Current[166ps] Ch1 Control1 Fine Delay............. - Current[166ps] Ch1 Control2 Fine Delay............. - Current[124ps] Ch1 Control3 Fine Delay............. - Current[110ps] Ch1 Command Fine Delay.............. - Current[262ps] Ch2 Clock Crossing Setting.......... - Nominal DIMM3 Clock Fine Delay.............. - Current[1346s] DIMM4 Clock Fine Delay.............. - Current[1346ps] Ch2 Control0 Fine Delay............. - Current[14ps] Ch2 Control1 Fine Delay............. - Current[56ps] Ch2 Control2 Fine Delay............. - Current[0ps] Ch2 Control3 Fine Delay............. - Current[0ps] Ch2 Command Fine Delay.............. - Current[110ps] Ch1 Ch2 Common Clock Setting........ - Nominal Ch1 RDCAS GNT-Chip Delay............ - Auto Ch1 WRCAS GNT-Chip Delay............ - Auto Ch1 Command To CS Delay............. - Auto . Ch2 RDCAS GNT-Chip Delay............ - Auto Ch2 WRCAS GNT-Chip Delay............ - Auto Ch2 Command To CS Delay............. - Auto Flex Memory Mode..................... - Auto CAS Latency Time (tCL)............... - 5 RAS# to CAS# Delay (tRCD)............ - 5 RAS# Precharge (tRP)................. - 5 Precharge Delay (tRAS)............... - 15 All Precharge to Act................. - Auto REF to ACT Delay (tRFC).............. - 52 Performance Level.................... - 8 >Read delay phase adjust Press Enter: Channel 1 Phase 0 Pull-In........... - Auto Channel 1 Phase 1 Pull-In........... - Auto Channel 1 Phase 2 Pull-In........... - Auto Channel 1 Phase 3 Pull-In........... - Auto Channel 1 Phase 4 Pull-In........... - Auto Channel 2 Phase 0 Pull-In........... - Auto Channel 2 Phase 1 Pull-In........... - Auto Channel 2 Phase 2 Pull-In........... - Auto Channel 2 Phase 3 Pull-In........... - Auto Channel 2 Phase 4 Pull-In........... - Auto Write to PRE Delay (tWR)............ - Auto Rank Write to Read (tWTR)........... - Auto ACT to ACT Delay (tRRD)............. -Auto Read to Write Delay (tRDWR)......... - Auto Ranks Write to Write (tWRWR)........ - Auto Ranks Read to Read (tRDRD).......... - Auto Ranks Write to Read (tWRRD)......... - Auto ALL PRE to Refresh.................. - Auto >Voltage Settings: CPU VID Control..................... – Auto 1,2350V CPU VID Special Add................. - Disabled CPU VID Special Add................. – 103.30% DRAM Voltage Control................ - 1.89v SB Core/CPU PLL Voltage............. - 1.55v NB Core Voltage..................... - 1.312v CPU VTT Voltage..................... – 1.240v Vcore Droop Control................. - Disabled Clockgen Voltage Control............ - 3.45v GTL+ Buffer Strength................ - Strong CPU GTL 0 REF Volt.................. - 0.6675 CPU GTL 2 REF Volt.................. - 0.6675 CPU GTL 1 REF Volt.................. - 0.6675 CPU GTL 3 REF Volt.................. - 0.6675 North Bridge GTL 0 REF Volt......... - 0.6650 North Bridge GTL 1 REF Volt......... - 0.6650 FSB Vref............................ - 21 Genie BIOS Settings: Exist Setup Shutdown................ - Mode 2 Exist Shutdown After AC loss........ - Enabled AC Shutdown Free.................... - Enabled O.C Clock Fail Retry Counter........ - 1 O.C Clock Fail CMOS Reloaded........ - Disabled CPU Clock Ratio..................... – 8.5 Target CPU Clock.................... - 4000 MHz CPU Clock........................... - 470 Boot Up Clock....................... - Auto CPU Clock Amplitude................. - 800mV CPU Clock0 Skew..................... - 200ps CPU Clock1 Skew..................... - 100ps DRAM Speed.......................... - 333/800 Target DRAM Speed................... - 1129MHz PCIE Clock.......................... - 102mhz
Code:>CPU Feature: Thermal Management Control.......... - Enabled PPM(EIST) Mode...................... - Enabled Limit CPUID MaxVal.................. - Enabled CIE Function........................ - Disabled Execute Disable Bit................. - Enabled Virtualization Technology........... - Enabled Core Multi-Processing............... - Enabled >DRAM Timing: Enhance Data transmitting........... - Normal Enhance Addressing.................. - Normal T2 Dispatch......................... - Disabled >Clock Setting Fine Delay Press Enter: DLL And RCOMP Settings.............. - Manual Ch1 Dram Defaul Skew................ - Model 5 Ch2 Dram Defaul Skew................ - Model 5 RCOMP Settings...................... - Model 1 Fine Delay Step Degree.............. - 70ps Ch1 Clock Crossing Setting.......... - Nominal DIMM1 Clock Fine Delay.............. - Current[1346ps] DIMM2 Clock Fine Delay.............. - Current[1346ps] Ch1 Control0 Fine Delay............. - Current[166ps] Ch1 Control1 Fine Delay............. - Current[166ps] Ch1 Control2 Fine Delay............. - Current[124ps] Ch1 Control3 Fine Delay............. - Current[110ps] Ch1 Command Fine Delay.............. - Current[262ps] Ch2 Clock Crossing Setting.......... - Nominal DIMM3 Clock Fine Delay.............. - Current[1346s] DIMM4 Clock Fine Delay.............. - Current[1346ps] Ch2 Control0 Fine Delay............. - Current[14ps] Ch2 Control1 Fine Delay............. - Current[56ps] Ch2 Control2 Fine Delay............. - Current[0ps] Ch2 Control3 Fine Delay............. - Current[0ps] Ch2 Command Fine Delay.............. - Current[110ps] Ch1 Ch2 Common Clock Setting........ - Nominal Ch1 RDCAS GNT-Chip Delay............ - Auto Ch1 WRCAS GNT-Chip Delay............ - Auto Ch1 Command To CS Delay............. - Auto . Ch2 RDCAS GNT-Chip Delay............ - Auto Ch2 WRCAS GNT-Chip Delay............ - Auto Ch2 Command To CS Delay............. - Auto Flex Memory Mode..................... - Auto CAS Latency Time (tCL)............... - 5 RAS# to CAS# Delay (tRCD)............ - 5 RAS# Precharge (tRP)................. - 5 Precharge Delay (tRAS)............... - 15 All Precharge to Act................. - 6 REF to ACT Delay (tRFC).............. - 52 Performance Level.................... - 10 >Read delay phase adjust Press Enter: Channel 1 Phase 0 Pull-In........... - Auto Channel 1 Phase 1 Pull-In........... - Auto Channel 1 Phase 2 Pull-In........... - Auto Channel 1 Phase 3 Pull-In........... - Auto Channel 1 Phase 4 Pull-In........... - Auto Channel 2 Phase 0 Pull-In........... - Auto Channel 2 Phase 1 Pull-In........... - Auto Channel 2 Phase 2 Pull-In........... - Auto Channel 2 Phase 3 Pull-In........... - Auto Channel 2 Phase 4 Pull-In........... - Auto Write to PRE Delay (tWR)............ - Auto Rank Write to Read (tWTR)........... - Auto ACT to ACT Delay (tRRD)............. -Auto Read to Write Delay (tRDWR)......... - Auto Ranks Write to Write (tWRWR)........ - Auto Ranks Read to Read (tRDRD).......... - Auto Ranks Write to Read (tWRRD)......... - Auto ALL PRE to Refresh.................. - Auto >Voltage Settings: CPU VID Control..................... – Auto 1,2350V CPU VID Special Add................. - Disabled CPU VID Special Add................. – 112.99% DRAM Voltage Control................ - 1.89v SB Core/CPU PLL Voltage............. - 1.55v NB Core Voltage..................... - 1.465v CPU VTT Voltage..................... – 1.351v Vcore Droop Control................. - Disabled Clockgen Voltage Control............ - 3.60v GTL+ Buffer Strength................ - Strong CPU GTL 0 REF Volt.................. - 0.6450 CPU GTL 2 REF Volt.................. - 0.6450 CPU GTL 1 REF Volt.................. - 0.6450 CPU GTL 3 REF Volt.................. - 0.6450 North Bridge GTL 0 REF Volt......... - 0.6750 North Bridge GTL 1 REF Volt......... - 0.6750 FSB Vref............................ - 23 Genie BIOS Settings: Exist Setup Shutdown................ - Mode 2 Exist Shutdown After AC loss........ - Enabled AC Shutdown Free.................... - Enabled O.C Clock Fail Retry Counter........ - 1 O.C Clock Fail CMOS Reloaded........ - Disabled CPU Clock Ratio..................... – 8.5 Target CPU Clock.................... - 4199 MHz CPU Clock........................... - 494 Boot Up Clock....................... - Auto CPU Clock Amplitude................. - 800mV CPU Clock0 Skew..................... - 200ps CPU Clock1 Skew..................... - 100ps DRAM Speed.......................... - 333/667 Target DRAM Speed................... - 996MHz PCIE Clock.......................... - 102mhz
Mit Zitat antworten
Zitat von Ewu80
.
| welcome to the zone - s.t.a.l.k.e.r. | 
Lesezeichen